Materialload Material quantity reference

Subfloor calculator

Subfloor panels are counted in 4 × 8 sheets. Enter the floor area and get the sheet count, with adhesive and screw quantities alongside.

Subfloor calculator live
ft
ft
%

Tongue-and-groove panels lose about 2 in per sheet to the joint — 32 sq ft is close enough for ordering.

sq ft
$
You need
— sheets
—
Area —
With waste —
Waste —
Per sheet —
Material cost $—
Check subfloor panels prices

Affiliate link. The cost above is units × the price you entered — it is not a quote.

A 300 sq ft floor takes 11 sheets of 4 × 8 tongue-and-groove subfloor once a 10% allowance is applied — 330 sq ft of panel against 300 sq ft of floor.

What the calculator assumes

  • 32 sq ft per 4 × 8 panel, with tongue-and-groove edges. A T&G panel loses about 2 inches of width to the joint, so 32 sq ft is a slight overestimate — which is the safe direction.
  • Waste defaults to 10%. A rectangular floor with joists at 16 inches can be laid with 5%; a floor broken up by stair openings and closets needs 12%.
  • Area is the floor area, not the room area. Measure to the centre of the walls under the drywall.
  • No allowance for stairs. Landings and treads are separate pieces cut from a sheet, so add a sheet if the stair opening is inside the calculated area.

Subfloor by joist spacing

Joist spacing Minimum panel Common choice
12 in 5/8 in 23/32 T&G
16 in 23/32 in 23/32 T&G
19.2 in 23/32 in 7/8 in
24 in 7/8 in 1 in T&G

Going one step thicker than the table is cheap insurance against a floor that feels soft between joists and a tile installation that cracks.

What goes with the panels

Per 100 sq ft of subfloor:

  • Construction adhesive: 1 tube per 2–3 panels.
  • Screws: 40–50 per panel, 1⅝ inch for 23/32 over wood joists, at 6 in edges and 12 in field.
  • Panel clips: not used on T&G, only on square-edge panels between joists.
  • Stair adhesive or blocking: wherever a panel edge lands between joists, add blocking rather than trusting the joint.

Where the number goes wrong

Laying panels end-joint to end-joint. Stagger the short ends by at least one joist bay. Four panels sharing one joint is a hinge, and the floor will move there forever.

Measuring the room, not the framing. A 20 × 15 room is 300 sq ft of floor but the panel has to run under the wall to the rim joist.

Cutting tightly around openings. Stairs and chases need a 1/4 inch gap, and the panels around them are cut from full sheets — which is where the 10% goes.

FAQ

Subfloor panels questions

How many sheets of subfloor for 1000 square feet?

About 35 sheets of 4 × 8 at a 10% allowance. 1,000 sq ft plus 10% is 1,100 sq ft, and each sheet covers 32 sq ft — so 35 sheets, or 34 if the layout is a clean rectangle.

Should subfloor be glued as well as screwed?

Yes. A bead of construction adhesive on the joists plus screws at 6 inches on edges and 12 in the field removes most floor squeak and stiffens the floor noticeably. Glue is about $6 a tube and covers 2–3 sheets.

Do I need a gap between subfloor panels?

Yes — 1/8 inch at the ends and 1/16 inch at the tongue-and-groove edges. Panels expand with humidity, and a tight floor buckles at the seams. The tongue provides the spacing at edges if you do not force it home.

What thickness subfloor do I need?

23/32 inch (3/4 nominal) for joists at 16 inches, 7/8 inch or tighter spacing at 24 inches. Thickness is set by the span, and the finish floor does not add stiffness.

REL

Related calculators