Materialload Material quantity reference

Plywood calculator

Sheathing is ordered in 32 sq ft sheets. Enter the area you are covering and get the sheet count with a cut allowance already applied.

Plywood calculator live
ft
ft
%

Sheathing goes down with 1/8 in gaps, so 32 sq ft per sheet is a slight overestimate — which is the safe direction.

sq ft
$
You need
— sheets
—
Area —
With waste —
Waste —
Per sheet —
Material cost $—
Check plywood prices

Affiliate link. The cost above is units × the price you entered — it is not a quote.

320 sq ft of sheathing takes 11 sheets of 4 × 8 plywood once an 8% allowance for cuts is applied — 345 sq ft of board against 320 sq ft of area.

What the calculator assumes

  • 32 sq ft per sheet, the area of a 4 × 8 panel. Change the coverage field for 4 × 10 (40) or 4 × 12 (48) panels.
  • Waste defaults to 8%. Roofs with hips, valleys and dormers need 15%; a flat rectangular floor needs 5%.
  • Area is the covered surface, measured to the outside of the framing. For a roof, that is the sloped area, not the plan area.
  • No deduction for openings — small ones are cut out and the offcut rarely goes back in.

Panels and where they go

Application Thickness Sheet Notes
Roof sheathing 7/16–15/32 in 4 × 8 24 in rafter spacing max
Wall sheathing 7/16 in 4 × 8 Braced walls may need 15/32
Subfloor 23/32 in T&G 4 × 8 Glue and screw, not just nail
Underlayment 1/4–3/8 in 4 × 8 Over existing subfloor
Shed floor 3/4 in 4 × 8 Pressure treated if near ground

Thickness is set by joist spacing and load, not by what is in stock. Going thinner than the span table allows is the one mistake that shows up as a bouncy floor rather than a visible defect.

Fasteners and clips

Per 100 sq ft of sheathing:

  • 8d common nails: 150–200 for wall sheathing at 6 in edges.
  • Roofing nails: 200–250 for roof sheathing at 6/12 spacing.
  • Panel clips: one per rafter bay on roof edges, where the panel lands between supports.
  • Construction adhesive: one tube per 2–3 sheets on subfloor.

Glue on a subfloor is the cheapest upgrade in the whole build. It removes most of the squeak before it exists.

Where the number goes wrong

Using plan area for a roof. A 6/12 pitch roof covers 12% more than its footprint; a 10/12 covers 30%. Use the sloped area or add the pitch factor.

Forgetting the gable ends. Gable wall sheathing is a triangle, and a triangle cut from a rectangle wastes most of the panel.

Ordering the exact count. Panels come in lifts of 30–50 and yards will not break one. Order the lift for a whole job and return the unopened ones if the policy allows.

FAQ

Plywood questions

How many square feet is a sheet of plywood?

32 sq ft for a 4 × 8 sheet, 48 for 4 × 12, 40 for 4 × 10. Sheathing is nominally 4 × 8 but measures 48½ × 96½ inches to leave expansion gaps, so 32 sq ft is slightly conservative.

How much waste should I allow for plywood?

8–10% for a simple rectangular deck or wall. A roof with hips and valleys needs 15%, and a room with lots of corners needs 12%. Waste on sheathing comes from cuts you cannot reuse, not from damage.

What thickness of plywood for a floor?

3/4 inch (23/32) for joists at 16 inches, with tongue-and-groove edges. 5/8 inch works at 16 inches and sags at 24. Subfloor thickness is set by joist spacing, not by the finish floor.

OSB or plywood?

Both are 4 × 8 and both work. OSB is cheaper and holds a nail well; plywood handles moisture better and weighs slightly less. For roof sheathing in a wet climate, plywood is the safer choice.

REL

Related calculators