Tile calculator
Tile is sold by the box, and the box covers a fixed area. Enter your room size and the coverage on the box to get boxes, area and cost.
A 12 × 12 tile covers 1 sq ft, so a 10 sq ft box holds 10 tiles. Diagonal layouts waste more — use 15%.
Affiliate link. The cost above is units × the price you entered — it is not a quote.
A 12 × 10 ft floor is 120 sq ft. With a 10% allowance for cuts that is 132 sq ft, or 14 boxes of 10 sq ft tile — plus one spare box kept for future repairs.
What the calculator assumes
- Coverage per box is 10 sq ft, which is a common box size for 12 × 12 tile. Change the field to whatever the box says — it is the only number that matters.
- Waste defaults to 10%, appropriate for a straight lay in a square room. Diagonal and herringbone patterns need 15%; small rooms with lots of cuts need 20%.
- Area includes the whole floor, under the cabinets and under the toilet. Tiling under the vanity is normal and cheaper than cutting around it.
- No allowance for grout or substrate. Thinset and backer board are separate calculations, and so is the levelling compound the floor will probably need.
Waste by layout
| Layout | Waste | Why |
|---|---|---|
| Straight lay, square room | 10% | Edge cuts are reusable |
| Straight lay, many corners | 15% | Cuts rarely transfer |
| Diagonal (45°) | 15% | Every edge cut is a triangle |
| Herringbone | 20% | Two directions of cut |
| Large format (24 in+) | 15% | Narrow offcuts are unusable |
Buy the spare box regardless of layout. Tiles are discontinued, dye lots shift between production runs, and a cracked tile ten years from now cannot be matched by a sample chip.
What goes under the tile
- Backer board or uncoupling membrane on floors: 1/4 inch over plywood, 1/2 inch in wet areas.
- Thinset: a 50 lb bag covers 60–80 sq ft with a 1/4 × 1/4 in trowel, less with a larger notch.
- Grout: a 10 lb bag covers 50–80 sq ft depending on tile size and joint width.
- Spacers and levelling clips: one per tile edge.
Where the number goes wrong
Trusting the tile count instead of the box. Boxes vary, and two products with identical tiles can hold 10 and 15. Always calculate from the box coverage.
Forgetting the substrate thickness. Backer board raises the floor by 1/4 inch, which shows at door thresholds and at the transition to carpet.
Cutting the last row too thin. If the layout leaves a 1 inch sliver at one wall, shift the whole grid by half a tile — the waste is the same, the result is much better.
Tile questions
How many boxes of tile for 100 square feet?
Eleven boxes of 10 sq ft tile with 10% waste, or ten boxes if you are buying 12 sq ft boxes. Always check the coverage printed on the box — it varies from 8 to 15 sq ft for the same nominal tile size.
How much extra tile should I buy?
10% for a straight lay in a rectangular room, 15% for a diagonal or herringbone pattern, and 20% for a room with many corners. Keep one box sealed afterwards for repairs — dye lots change.
How many 12 × 12 tiles are in a box?
It depends on the box, not the tile. A 12 × 12 tile is 1 sq ft, so a 10 sq ft box holds 10 tiles and a 15.5 sq ft box holds 15. Count the pieces on the label before ordering.
How much tile do I need for a backsplash?
Measure length × height in inches, divide by 144 for sq ft, then add 15% for outlets and edge cuts. A 10 ft backsplash at 18 inches high is 15 sq ft, which is 17 sq ft with waste.