Materialload Material quantity reference

Mortar calculator

Mortar is bought by the bag and used by the trowel. Enter the wall area and get the bag count, with the blocks-per-bag figure stated.

Mortar calculator live
ft
ft
%

One 80 lb bag of Type S lays roughly 35 block faces — about 31 sq ft of wall.

sq ft
$
You need
— bags
—
Area —
With waste —
Waste —
Per bag —
Material cost $—
Check mortar prices

Affiliate link. The cost above is units × the price you entered — it is not a quote.

An 80 sq ft block wall takes about 2.7 bags of 80 lb mortar — buy 3. One bag lays roughly 35 standard 8 × 8 × 16 blocks, which is 31 sq ft of wall face.

What the calculator assumes

  • One 80 lb bag covers about 31 sq ft of block wall, which is 35 standard blocks. The figure comes from the manufacturer’s yield and assumes a 3/8 inch joint.
  • Block, not brick. Brick walls use far less mortar per unit area. If you are laying brick, set the coverage field to 90–100 sq ft per bag.
  • A single wythe. A cavity wall or a grouted wall needs more, because there are more joints and some mortar goes into the cores.
  • Waste defaults to 5%. Mortar is mixed in batches and the last half-bag always sets before it is used.

Mortar yield by masonry type

Masonry Units per bag Wall per bag
8 × 8 × 16 block 35 31 sq ft
8 × 8 × 8 half block 35 15.5 sq ft
Modular brick 100–120 60–70 sq ft
4 in clay brick, running bond 110 65 sq ft
Stone veneer 20–25 sq ft 20–25 sq ft

Stone veneer is the outlier: irregular stone takes far more mortar per square foot because the joints are thick and unpredictable. Budget 40% more than the flat-wall figure.

Bags, mixing and the two-hour window

Mortar is workable for about two hours after mixing. That is the real constraint on a bag count, not the arithmetic:

  • Mix what you can lay in 90 minutes. On a first block wall that is 40–60 blocks, so two bags at a time.
  • Do not retemper. Adding water to mortar that has begun to set weakens it permanently. Discard and mix fresh.
  • Bagged versus site-mixed. A bag of pre-blended mortar costs more per pound than sand and cement, but for anything under 200 blocks it is cheaper than buying three ingredients and a mixing tub.

Where the number goes wrong

Estimating from the block count only. 100 blocks is 2.9 bags by the 35-per-bag rule, but the first course on a footing always uses more because the bed has to level out the concrete.

Forgetting the cores. A grouted wall needs grout as well as mortar, and they are different bags. Grout fills the cores; mortar joins the faces.

Buying for the whole wall at once. Bags keep for months in a dry place, so buying the batch is fine — but mortar that has absorbed moisture from a damp shed is unusable. Store it off the floor.

FAQ

Mortar questions

How many blocks will one bag of mortar lay?

About 35 standard 8 × 8 × 16 blocks, or roughly 31 sq ft of wall. Brick is different: a bag covers 100–120 bricks because the joints are smaller and the units are lighter.

What mix ratio should mortar be?

Type S for block and most exterior work, at 3 parts sand to 1 part cement plus hydrated lime. Type N is softer and suits above-grade brick. Buying bagged mortar removes the guesswork — the ratio is already in it.

How thick should mortar joints be?

Three-eighths of an inch for block, three-eighths to half an inch for brick. Joint thickness is what the coverage figures assume; fatter joints use noticeably more mortar.

Can I use too much mortar?

Yes — squeezing it into the cores or leaving it thick in the bed wastes material and weakens the wall. Mortar is glue, not filler. Excess that oozes out gets struck off with the trowel, not pushed back in.

REL

Related calculators