Deck stain calculator
Deck stain is sold by the gallon and covers a fixed area per coat. Enter the deck size and the coverage from the can to get gallons and cost.
250 sq ft per gallon is typical for a semi-transparent stain on smooth decking. Solid colour covers more; a rough, weathered deck drinks far more.
Affiliate link. The cost above is units × the price you entered — it is not a quote.
A 12 × 10 ft deck is 120 sq ft. Two coats at 250 sq ft per gallon, plus 5% for edges and touch-ups, comes to 252 sq ft — so buy 2 gallons. One gallon will not carry a second coat.
What the calculator assumes
- Coverage is 250 sq ft per gallon, which is typical for a semi-transparent stain on smooth decking. Change the field to whatever your can says — it is the only number that matters.
- Two coats. Bare wood needs two; a deck stained last year and still beading water needs one.
- 5% extra, which covers the cut ends, the edges of the boards and the touch-ups you will do after the first coat dries unevenly.
- Deck boards only. Railings, steps, fascia and lattice are not in the area. On a deck with a full railing, that is 20% more surface than the deck itself.
Coverage by stain type
| Product | Coverage per gallon | Coats |
|---|---|---|
| Transparent / clear sealer | 250–350 sq ft | 2 |
| Semi-transparent stain | 250–300 sq ft | 2 |
| Solid colour stain | 300–400 sq ft | 2 |
| Stain on rough or weathered decking | 150–200 sq ft | 2 |
| Restorer / brightener | 200–300 sq ft | 1 |
The spread between the best and worst case is more than double. That is not marketing — a 20-year-old pressure-treated deck with raised grain absorbs roughly twice what a new, smooth-surfaced board does, and no table can tell you which one you have.
The same coverage chain drives the paint, primer and tile pages; every rate we assume, with its default waste, is in the coverage table.
How the area is measured
Measure the deck as a rectangle from the outside edge of the rim joist, not the inside of the railing. Boards run to the edge, and the fascia gets coated too.
For an L-shaped or multi-level deck, split it into rectangles, calculate each, and add them. The calculator handles one rectangle at a time, so run it twice and sum the gallons.
Railings are the usual miss: a top rail is 5.5 in wide and 2 sides get coated, a bottom rail the same, and balusters are 1.5 in square with four faces. A 100 ft railing with 2 in balusters at 4 in centres is close to 90 sq ft of surface — nearly as much as a 10 × 10 deck.
Where the number goes wrong
Staining over a wet deck. New pressure-treated wood needs four to six weeks to dry, and the test is simple: sprinkle water on it. If it beads, the wood is still sealed and the stain will sit on the surface and peel.
Buying one gallon for one coat. Stain is not paint — you cannot stretch it, and a thin coat on bare wood fails first at the board ends and the joints, which is exactly where water gets in.
Skipping the back-brushing. Working stain into the grain adds time but removes the difference between 300 sq ft per gallon and 180. A sprayed-only deck uses more product, not less, because half of it misses.
Forgetting temperature. Most stains need 50 °F and rising, with no rain for 24 hours. A deck stained in the evening in October will look perfect and fail by spring.
Deck stain questions
How many gallons of stain for a 12 × 10 deck?
Two gallons at 250 sq ft per gallon for two coats. The deck is 120 sq ft; two coats is 240 sq ft; with 5% extra that is 252 sq ft, and 252 ÷ 250 rounds up to 2 gallons.
Does a deck need one coat or two?
Two on bare or previously unstained wood, one on a deck that was stained last season and still beads water. A single coat on bare wood leaves the grain partly unprotected, and the second coat is what gives an even colour.
How many square feet does a gallon of deck stain cover?
250 to 300 sq ft for a semi-transparent stain, 300 to 400 for a solid colour, and as little as 150 on a rough, weathered or deeply grooved deck. The can is more reliable than any table — read it before ordering.
Do I need to include the railings?
Yes, and they are usually underestimated. A 100 linear ft railing with top, bottom and balusters can add 60 to 100 sq ft of surface. Measure the flat faces you will actually coat, or add a flat 20% to the deck area for a full railing.
How long before I can stain a new deck?
Four to six weeks for new pressure-treated lumber, until it stops beading water when you sprinkle it. Staining wet wood traps moisture under the film and the finish peels within a season. Rain within 24 hours of application does the same thing.