Materialload Material quantity reference

Fence calculator

A fence is bought in pieces, not in square feet. Enter the run length and picket size to get pickets, posts, rails and post concrete.

Fence calculator live
ft
in
in
ft
$
$
%

Posts every 8 ft is the standard for a 6 ft privacy fence. Going to 10 ft saves two posts but the rails sag within a season.

You need
— pickets
—
Posts —
Rails —
Pickets —
Post concrete —
Material cost $—
Check fence prices

Affiliate link. The cost above is a bill of materials at the prices you entered — it is not a quote, and it excludes labour and delivery.

A 100 ft privacy fence with 5.5 in pickets and a 1/8 in gap needs 224 pickets, 14 posts at 8 ft centres, and 27 eight-foot rails. Budget two 80 lb bags of concrete per post — 28 bags in total.

What the calculator assumes

  • A straight run. Every corner, gate and step adds posts and breaks the even bay spacing. Measure each straight section separately and add the results.
  • Pickets are counted by pitch — picket width plus gap — not by area. A 5.5 in picket with a 1/8 in gap covers 5.625 in of fence line, so 100 ft needs 213 of them.
  • Posts are spaced from the start of the run, with one at each end. A 100 ft run at 8 ft centres gives 13 bays and 14 posts, and the 13th bay is 4 ft.
  • Rails are 8 ft, one per bay per rail line. Two rails on a 100 ft fence is 200 linear feet, or 27 boards once you allow 5% for the bays that are not 8 ft.
  • Waste defaults to 5%. Pickets split, end boards get ripped, and one in twenty boards has a defect worth rejecting.

Pickets per 100 ft

Picket width Gap Pitch Pickets (with 5%)
3.5 in 1/4 in 3.75 in 336
5.5 in 3/4 in 6.25 in 202
5.5 in 1/4 in 5.75 in 220
5.5 in 1/8 in 5.625 in 224

The pattern is worth internalising: a 1/8 in change in gap moves the count by four to five pickets per hundred feet. On a 300 ft property line that is a $30 difference, which is why the gap belongs in the quote rather than in the installer’s head.

The count rule itself — run ÷ pitch, then posts as bays + 1 — is set out with the stock lengths and waste defaults on the method page.

Posts per 100 ft

Post spacing Bays Posts
6 ft 17 18
8 ft 13 14
10 ft 10 11

Most residential privacy fence is built at 8 ft because rails and panels come in 8 ft lengths. Going to 10 ft saves three posts per hundred feet and costs you a sagging rail line by the second summer.

Post depth and concrete

A post hole is a cylinder, and the concrete volume is what it is: a 10 in diameter hole 30 in deep holds 1.36 cu ft. An 80 lb bag of fast-setting mix yields about 0.6 cu ft, so two bags fill it with a little to spare.

Two things matter more than the exact bag count:

  • Gravel at the bottom. Six inches of crushed stone under the post lets water drain away from the end grain. A post that sits in a concrete cup rots from the bottom up in about ten years.
  • Depth below frost. In the northern states the frost line is the controlling number, not the post height. A 6 ft fence with 2 ft posts set in a 48 in frost depth needs longer posts than the fence height suggests.

Where the number goes wrong

Measuring the property line instead of the fence line. Setbacks, gates and the corner posts all consume length. Walk the run with a tape and mark each post position before ordering.

Ignoring slope. A fence on a grade is either stepped (posts at different heights, rails level) or racked (rails following the slope). Stepped fences use slightly more pickets because the bottom of each bay is trimmed.

Ordering pickets by the panel count. A “6 ft panel” is a nominal size. The actual picket count in a pre-assembled panel varies by manufacturer, and the panel width is often 5 ft 11 in to leave room for the post.

Forgetting the gate. A gate needs two heavier posts, its own frame and hinges, and typically a diagonal brace. None of that is in the picket count.

FAQ

Fence questions

How many pickets do I need for 100 ft of fence?

224 with 5.5 in pickets, a 1/8 in gap and 5% spare. The arithmetic is 1,200 in of run ÷ 5.625 in per picket = 213 pickets, plus 5% for the ones that split or get cut at the ends. Wider gaps cut the count quickly: a 3/4 in gap drops it to 202.

How many posts for 100 ft of fence?

14 at 8 ft centres. The count is bays plus one, and the last bay is usually shorter than the rest — 12 bays of 8 ft plus one of 4 ft. Do not stretch the spacing to make the bays even; posts set at 10 ft sag within a season.

How much concrete per fence post?

Two 80 lb bags for a 4 × 4 post in a 10 in hole 30 in deep. That hole is 1.36 cu ft, and an 80 lb bag yields about 0.6 cu ft. If you are using 50 lb bags, budget three per post instead of two.

How deep should fence posts be set?

A third of the post above ground is the rule most fence crews use, with a 6 in gravel base for drainage. In cold climates the hole has to go below the frost line, which can be 36 to 48 in — deeper than the post height rule would suggest.

How many rails does a fence need?

Two for a 6 ft privacy fence, three above 6 ft or where wind load matters. Rails run horizontally between posts and are usually sold in 8 ft lengths, which is why post spacing and rail length are tied together.

What gap should I leave between pickets?

1/8 to 1/4 in for privacy, 3 to 4 in for a spaced or shadowbox fence. Wood swells in wet weather, so a fence built tight in a dry month will buckle by spring — the gap is a expansion joint, not a design detail.

REL

Related calculators